Maintenance Check: MOVA Z60 Ultra Roller Complete

MOVA Z60 Ultra Roller Complete at a Glance

• Suction Power: 28,000 Pa
• Mopping System: HydroForce continuously washed roller mop, 12 spray nozzles, 10.08-inch roller
• Mop Pressure: 4,100 Pa of downward pressure, 17N
• Dock Mop Wash: Up to 176°F hot-water wash
• Dock Drying: Hot-air drying
• Auto-Empty Bag: 3.2 L, up to 100 days
• Navigation: Retractable VersaLift lidar, dual RGB cameras, 3D structured light, 200-plus objects recognized
• Brush System: TroboWave DuoBrush, rubber and rubber-bristle rollers
• Robot Height: 3.78 inches with lidar retracted
• Cleaning Solution: DuoSolution dual-compartment automatic dispensing

Main Brushes, Side Brush and Wheels (Every 2–3 Days)

Dual Main Brushes and Brush Compartment

Remove wrapped hair and debris from both brushes. Check the ends and clear dirt from the brush compartment.

[Image: Dual main brushes and brush compartment]

Side Brush Gear

Clear hair and strands from the extending side brush and its gear housing. Check that the brush moves freely.

[Image: Side brush gear]

Wheels

Remove hair and debris from the main wheels, omnidirectional wheel and caster wheel. Check the axles for wrapped strands.

[Image: Wheels]

Water Tanks, Dustbin and Filters (Weekly)

Dirty-Water Tank

Empty after each use to prevent odors. Rinse away residue and clean the interior as needed.

[Image: Dirty-water tank]

Clean-Water Tank

Check the water level and refill as needed. Rinse away residue and inspect the scale inhibitor.

[Image: Clean-water tank]

Internal Dirty-Water Box

Remove the robot's dirty-water box, empty any collected water and rinse it with clean water. Dry before reinstalling.

[Image: Internal dirty-water box]

Dustbin

Remove and empty any remaining debris. Rinse with clean water as needed and dry completely before reinstalling.

[Image: Dustbin]

Underneath Dustbin Area

Check the suction opening and surrounding compartment for trapped hair, dust and debris.

[Image: Underneath dustbin area]

Main Filter

Gently tap accumulated dust from the filter to maintain airflow. Rinse with clean water if needed and allow it to dry completely. Do not scrub the filter.

[Image: Main filter]

Dirt Funnel Barrier

Clear hair and debris from the dirt funnel barrier. Check for buildup that could restrict debris pickup.

[Image: Dirt funnel barrier]

Sensors, Dock, Roller Mop and Dust Bag (Monthly)

Top and Front Sensors

Wipe the VersaLift lidar, edge sensor, cameras and 3D laser sensors with a soft, dry cloth. Remove dust and fingerprints.

[Image: Top and front sensors]

Bottom Sensors

Wipe the cliff and carpet sensors whenever dust or debris is visible.

[Image: Bottom sensors]

Charging Contacts

Clean the charging contacts on the robot and dock with a soft, dry cloth. Check the dock's signaling area for dust.

[Image: Charging contacts]

Washboard and Dock Basin

Remove the washboard after the mop-washing cycle finishes. Rinse away residue and clear debris from the basin before reinstalling.

[Image: Washboard and dock basin]

Roller Mop

Inspect the roller for trapped hair, lint and wear. Remove it for a more thorough cleaning when needed.

[Image: Roller mop]

Roller Mop Housing

Check the area surrounding the roller for accumulated dirt, hair and damp residue.

[Image: Roller mop housing]

Fluffing Roller

Remove the fluffing roller by pressing its release clips. Clear trapped fibers and residue before reinstalling.

[Image: Fluffing roller]

Mop Cover

Check the retractable mop cover for dirt and debris. Clean the edges and mounting points to keep it moving freely.

[Image: Mop cover]

Dust Bag

Confirm the dust bag is seated correctly and isn't full. Replace it when needed, generally every two to four months.

[Image: Dust bag]

Deep Clean (Every 1–3 Months)

Main Brush Compartment

Remove both brushes and thoroughly clean the compartment and brush holders. Watch for packed hair around the ends.

[Image: Main brush compartment]

Roller Mop Compartment

Remove the roller mop and clean accumulated dirt and damp residue from the housing. Let cleaned components dry before reassembly.

[Image: Roller mop compartment]

Roller Mop Slot and Filter Vent

Clear hair, lint and debris from the roller slot and filter vent. These areas can accumulate residue from the continuously washed mop.

[Image: Roller mop slot and filter vent]

Fluffing Roller Housing

Remove the fluffing roller and clean the surrounding compartment. Pay attention to trapped fibers and dried residue near the roller ends.

[Image: Fluffing roller housing]

Internal Water System

Remove the internal dirty-water box and check its openings for residue or blockages. Rinse and dry the removable box.

[Image: Internal water system]

Drain Area

With the washboard removed, clear hair, lint and dried residue from the dock's drainage openings.

[Image: Drain area]

Dock Ramp

Wipe the ramp's ridges and grooves to remove dirt that could interfere with docking.

[Image: Dock ramp]